Product Search

Gryphon 30V 10A Hyper BEC Polaris 12V (GSR-3030HV)


The Gryphon Polaris GSR-3030HV is a compact and lightweight 12V BEC system for Multicopter, FPV, RC Models..
It's light weight and compact size allow an installation in narrow environments, Please pay attention to the fact that the output current will depend on the input voltage on the unit, so make sure to perform preleminary tests on a secured workbench and install the Polaris BEC so that a sufficient airflow allows a proper cooling of the BEC if this is necessary

TECHNICAL SPECIFICATIONS
Input voltage : 14.8V~30V(4~7 LiPo Cells)
Output voltage : 12.2V
Output current : 3A(Continuous) @ 14.8V
2A(Continuous) @ 22.2V
3.5A Current Limit Cut-Off
Size : 9mm(H) x 15mm(W) x 34mm(L)
Weight : 7g (exc. Cables)

$59.95
$59.95


In Stock: Totally in stock right now

Gryphon 45V 15A Hyper BEC Agena (GSR-5045LMT)


Gryphon HV BEC AGENA (GSR-5045)

GSR-5045 is a BEC which is the best for using around 22.2V(6 Cells LiPo) battery voltage. Especially, when you use the battery only for 3 cells ~6 cells receiver, it's very good for it.

Specs:
Reg Type : Switching
Input Voltage Range : 11V ~ 45V (3~10 Cells)
Output voltage Range : 5.2V, 6.0V, 6.8V, 7.4V, 8.4V Selectable
Voltage ADJ : 4.8V~7.7V ADJ (Potentiometer)
Output currant(Peak) : 15A
Output currant(Cont) : 7A
Low voltage alarm setup : 10V~45V (Available GDB-1010 or GDB-1030)
On/Off Switch : Available (GSB-1010P, GSB-1010S, GSB-1030P, GSB-1030S)
Size : 12mm(H) x 31mm(W) x 52mm(L)
Weight : 14g (Excluding Cables)

$99.95
$99.95


In Stock: Totally in stock right now

Gryphon 75V 20A Hyper HV BEC Quasar (GSR-7075LMT)


GSR-7075 is a super 20A BEC with a huge input voltage range.

Specs:
Reg Type : Switching
Input Voltage Range : 11V ~ 75.6V (3~18 Cells)
Output voltage Range : 5.2V, 6.0V, 6.8V, 7.4V, 8.4V Selectable
Voltage ADJ : 4.8V~7.7V ADJ (Potentiometer)
Output currant(Peak) : 20A
Output currant(Cont) : 10A
Low voltage alarm setup : 10V~75V (Available GDB-1010 or GDB-1030)
On/Off Switch : Available (GSB-1010P, GSB-1010S, GSB-1030P, GSB-1030S)
Size : 12mm(H) x 31mm(W) x 52mm(L)
Weight : 20g (Excluding Cables)

$142.95
$142.95


In Stock: Sorry bro, Sold out

Gryphon Duo 2-Channel Voltage Regulator


If you're running unregulated LiPo or LiFe power to your servos, this regulator will allow you to run regulated current to your sensitive Gyro and Tail servo. Integrated heatsink allows for superior cooling.

Specs:
- Input Voltage: 6V to 10V (5-8 cell NiCd/NiMH or 2-cell LiFe/LiPo)
- Output Voltage: 5.2V or 6.0V, User Selectable
- Max Continuous Current: 3A @ 6.0V
- Max Peak Current: 10A @ 6.0V for 30sec
- Ports: Input 2CH, Output 2CH
- Size: 10mm x 23mm x 40mm (HxWxL)
- Weight: 9g

Includes main unit and 2 patchcables.

$33.00
$33.00


In Stock: Sorry bro, Sold out

Gryphon Extension Servo Wire Assembly


Wiring looms to suit all the range of Gryphon products and other R/C Products

$7.00
$7.00


In Stock: Totally in stock right now

Gryphon Ferrite Core EMC Clamp Filters (GCF-1518)


● Unique plastic case ensures simple, convenient installation and includes a self-holding mechanism to prevent slippage on cables.
● Ferrite core provides excellent absorption of high-frequency EMC.
2pcs/ 1Pack

Size : 18mm(L) x 15mm(ΦD)

$9.50
$9.50


In Stock: Totally in stock right now

Gryphon High Performance 615mm CF Blades Flybarless


- RED : 615 FBL
YELLOW : Coming Soon
Black : Coming Soon

- 615mm carbon Blades. They are good for Extreme 3D.

- Applied for all FB and FBL systems.

Specs:
- Length: 615mm
- Width: 55mm
- Root: 12mm
- Bolt Hole: 4mm

Includes:
- One pair of Gryphon blades.
- A neat Gryphon chamois.

Gryphon Blades are manufactured in Gryphon plants by Gryphon, instead of through OEM manufacturing.

All materials are from Korea and everything is produced in Korea. Proudly resulting in the best finishing process and high-end performance.

$95.00
$95.00


In Stock: Totally in stock right now

Gryphon High Power Flux LED Board (GDB-1030)


GDB-1030 Gryphon High Power Flux LED Board

Optional part for GVR-7020 Gryphon Extreme-Heli Voltage Regulator. Plugs into the AUX position on the regulator.

● This is the device that connected to Gryphon Product which has Low-voltage alarms, including GVR-7020.
● 1 Watt High Power Flux LED provides day light visibility up to 200 meters away.

$12.00
$12.00


In Stock: Totally in stock right now

Gryphon Low Voltage Display LED Board GDB-1010


GDB-1010 Gryphon Low Voltage Display LED Board

This optional accessory for the Gryphon Extreme-Heli Regulator plugs into the AUX position on the regulator.

Red LED's illuminate when a low-voltage condition is met. Low-voltage condition is user-selectable for LiFe or LiPo at the Voltage Regulator.

$11.00
$11.00


In Stock: Totally in stock right now

Gryphon Pin Flag Switch - Flux LED (GSB-1030P)


GSB-1030P Gryphon Pin Flag Switch - Flux LED

Optional part for GVR-7020 Gryphon Extreme-Heli Voltage Regulator.

●GSB-1030P is an Integrated Switch which features both "fail safe on switch" and "Low-voltage alarm LED".
● 1 Watt High Power Flux LED provides day light visibility up to 200 meters away.
● Can be used with any Gryphon product which has Low-voltage alarms, including GVR-7020.

$36.00
$36.00


In Stock: Totally in stock right now

Gryphon Pin-Flag Switch GSB-1010P


Gryphon Pin-Flag switch.

The Pin-Flag switch is a fail-safe-on type switch. If the switch is destroyed, the unit will remain ON. Only when the pin is inserted into the switch does the unit turn OFF.

Bight Blue LED activates when the switch is in the ON position.

Note: For use on the Scott Gray reg, you will need to swap the red and orange wire at the servo plug end

$18.00
$18.00


In Stock: Sorry bro, Sold out

Gryphon Power Disc Dual BEC (GSR-5030DM)


Power Disc BEC (GSR-5030DM) provides 5V and 12V outputs.

The Gryphon Power Disc Dual BEC.

Dual voltage BEC regulator designed for Multirotors systems.

It accepts voltages inputs from 14.4V up to 30V(4~7 LiPo Cells), and has 2 independant BEC outputs.

User selectable 5.6~8.4V, 5A on BEC1 output (For Camera, Retractable landing gears, Gimbal servos,flight controllers etc)

And 12V, 3.5A on BEC 2 output (Camera, Video Transmitter, LEDs..)

CONTENTS
1. Main PCB : 1 EA
2. Power Output Molex Connector Cable(L=30cm) : 11 EA
3. PCB Post Female-Female 3 x 5mm : 4 EA
4. PCB Post Female-Female 3 x 10mm : 4 EA
5. Socket button head screw M3 x 5mm : 8 EA
6. Socket button head screw M3 x 12mm : 4 EA
7. Power Input Molex Connector Cable Ass’y : 1 EA

SPECIFICATIONS
Input voltage : 14.4V~30V(3~7 LiPo Cells)
Output voltage : BEC1 : 5.6V, 6.0V, 7.4V, 8.4V Selectable
BEC2 : 12.0V
Output current : BEC1 : 5A(Continuous) @ 22.2V
BEC2 : 3.5A(Continuous) @ 22.2V
Size : (Φ)100mm x (H)11mm
Weight : 28g (Exc. Cables)

$126.00
$126.00


In Stock: Sorry bro, Sold out

Gryphon Power Distribution Board - Hex (GPD-1000HX)


Power Distribution Board (GPD-1000HX)
For HEXA Multicopter

SPECIFICATIONS
- Up to 6 ESC/Motor can be connect to the Board
- 260A (Continuous), 320A (Peak)
- 2 layout with 2oz(70um) Copper Dual PCB.
- Gold plated with black soldermask
- Φ64mm body mounting
- 1 PCB plate for(+), 1 PCB plate for(-)
- Weight : 52g
- Size : 100mm x 100mm

$68.00
$68.00


In Stock: Totally in stock right now

Gryphon Power Distribution Board - Hex with plugs (GPD-1000HXP)


Power Distribution Board (GPD-1000HXP)
For HEXA Multicopter (Equipped with 12 pair of 3.5mm plug)

SPECIFICATIONS
- Up to 6 ESC/Motor can be connect to the Board
- 260A (Continuous), 320A (Peak)
- 2 layout with 2oz(70um) Copper Dual PCB.
- Gold plated with black soldermask
- Φ64mm body mounting
- 1 PCB plate for(+), 1 PCB plate for(-)
- Weight : 74g
- Size : 105mm x 105mm

$88.00
$88.00


In Stock: Sorry bro, Sold out

Gryphon Power Distribution Board - Octo (GPD-1000CT)


Power Distribution Board(GPD-1000CT)
For OCTO Multicopter

SPECIFICATIONS
- Up to 8 ESC/Motor can be connect to the Board
- 260A (Continuous), 320A (Peak)
- 2 layout with 2oz(70um) Copper Dual PCB.
- Gold plated with black soldermask
- Φ64mm body mounting
- 1 PCB plate for(+), 1 PCB plate for(-)
- Weight : 53g
- Size : 100mm x 100mm

$73.00
$73.00


In Stock: Totally in stock right now

Gryphon Power Distribution Board - Octo with plugs (GPD-1000CTP)


Power Distribution Board(GPD-1000CTP)
For OCTO Multicopter (Equipped with 16 pair of 3.5mm plug)

SPECIFICATIONS
- Up to 8 ESC/Motor can be connect to the Board
- 260A (Continuous), 320A (Peak)
- 2 layout with 2oz(70um) Copper Dual PCB.
- Gold plated with black soldermask
- Φ64mm body mounting
- 1 PCB plate for(+), 1 PCB plate for(-)
- Weight : 85g
- Size : 105mm x 105mm

$99.95
$99.95


In Stock: Totally in stock right now

Gryphon Replacement Glow Plug Wire - Alligator (GEW-5530A)


Gryphon Replacement Glow Plug Wire - Alligator (GEW-5530A)

$8.00
$8.00


In Stock: Totally in stock right now

Gryphon Replacement Glow Plug Wire - Spring (GEW-5530S)


Gryphon Replacement Glow Plug Wire - Spring (GEW-5530S)

$8.00
$8.00


In Stock: Sorry bro, Sold out

Gryphon Slide Switch - Flux LED (GSB-1030S)


GSB-1030S Gryphon Slide Switch - Flux LED

Optional part for GVR-7020 Gryphon Extreme-Heli Voltage Regulator.

●GSB-1030S is an Integrated Switch which features both "fail safe on switch" and "Low-voltage alarm LED".
● 1 Watt High Power Flux LED provides day light visibility up to 200 meters away.
● Can be used with any Gryphon product which has Low-voltage alarms, including GVR-7020.

$28.50
$28.50


In Stock: Totally in stock right now

Gryphon Slide Switch GSB-1010S


Gryphon slide switch.

The slide switch is a fail-safe-on type switch. If the switch is destroyed, the unit will remain ON. Only when the sliding switch is moved to the OFF position will the unit turn OFF.

Bight Blue LED activates when the switch is in the ON position.

Note: For use on the Scott Gray reg, you will need to swap the red and orange wire at the servo plug end

$15.00
$15.00


In Stock: Sorry bro, Sold out

Hatori Exhaust Deverter Long 139


139 Hatori SB18/19/20 Replacement Exhaust Deverter

$9.00
$9.00


In Stock: Totally in stock right now

Hatori Muffler 56NS-3D (#566) (OS 55 / YS 56)


This tuned muffler is developed for 3D Flight, 53-56 Engines.
Not usable for 50 Engine.
Designed and produced for Power-Range of 16,500-20,000rpm

$92.75
$92.75


In Stock: Sorry bro, Sold out

Helio Spring Flight Controller


Truly Free

Supported by multiple open source flight controller software including ButterFlight’s 3.3+ most current technologies

Natively Fast

True 32khz processing without overclocking

IMU-F

Never before seen IMU-f system an advanced inline discrete filtered gyro that is transparent to the flight controller
With a super clean discrete filtered gyro, more processing power is available for flight controller logic and future feature updates without causing slowdown or issues during flight

Helio Gyro

The hardware contains both an f3 (IMU-F) and an f4. The gyro is a IMU 20601.

Tech Specs

Processors: F4 & F3, STM32F405 & STM32F301
IMU: ICM 20601
OSD: Full Betaflight OSD support
Motor Outputs: Full DSHOT and MULTISHOT support.
Receiver Support: PPM, S.Bus (inverter built-in), DSM, HoTT, SRXL, CSRF, FPort ready. 5V or 3.3V supply for receiver.
Telemetry Support: FrSKY Smart Port, FrSKY Sensor Hub, HoTT Telemetry, SRXL, CSRF, FPort ready. Built-in inverter for FrSKY telemetry.
Serial Ports: 5 full serial ports (UARTs). UART1 and UART2 have inverters for S.Bus and SmartPort telemetry.
Buzzer Port: Dedicated port for 5V (100mA max) buzzers.
Analog Inputs: Voltage sensing up to 26V, current and RSSI inputs (3.3V max).
Power: VBAT up to 6s with voltage regulator 2.5A continuous 3.2A burst. Or 5v in (switchable with jumper pads)

Important Notes:

Before soldering or mounting any flight controller, connect it to your PC and verify operation
Incorrect soldering techniques will damage this board and void warranty. Please use the correct sized tip, temperature and technique. Temp controlled soldering irons (such as the TS100) are available for under $100 and will make soldering much easier.
Lifted pads are a result of incorrect soldering techniques or excess mechanical pressure and will not be covered under warranty.
USB ports must be handled with care, breakage of usb ports are not covered under warranty
Always use a smoke stopper before powering your build for the first time.

$54.95
$54.95


In Stock: Sorry bro, Sold out

HGLRC 28A 4in1 ESC Replacement


HGLRC 28A 4in1 ESC Replacement for F325, F328, F425 and F428.

Size: 20X20MM

$48.95
$48.95


In Stock: Sorry bro, Sold out

HGLRC XJB F428-TX20 Omnibus F4 Flight Controller 28A 2-4S Blheli_S ESC Switchable VTX


So much power in such a small package!

The XJB stack represents incredible value, all jam-packed into a 20x20 format. Featuring betaflight OSD, switchable VTX with pitmode and a clean non swamping signal. 28A 4in1 ESC and enough CPU power to run 8k x 8k!

Specifications:

Model: HGLRC XJB F428-TX20
Weight: 6.5g
Usage: for 65mm-250mm Frame Kit
Micro F4 Flight Controller Board (with D-SHOT)

MPU: MPU6000-SPI
CPU: STM32F405RGT6, dual 8K.
Betaflight target: OMNIBUSF4
Black Box: Flash 16M
Input Voltage: 2-4S Lipo
Built-in Betaflight OSD to adjust PID
BEC Output: 5V@3A
Size: 25x25mm board, 20mm mounting holes (M2)
Weight:2.3g
Supports SBUS/PPM/DSMX receivers

28A 2-4S Blheli_S BB2 4 in 1 ESC:

Input Voltage: 2-4S Lipo battery
Constant Current: 28A
Peak Current: 35A
Firmware: BLheli_S 16.5
Size: 27x27mm (mainboard)
31x31mm ( including pad)
Installing Hole: 20x20mm, M2
Weight: 4.2g
CPU: SILABS EFM8BB2 48MHZ
MOS Tube: TOP QUALITY MOSFET
Firmware: BL-Heli 16.5
Supports, Damped Mode, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600, forward and reverse
HGLRC XJB-TX20 Mini FPV Transmitter

Output power: 0/25mW/100mW/250mW switchable
BAT: 7-24V,BEC 5V-3A
170mA----250mW
120mA----100mW
80mA----25mW
Video system: NTSC/PAL
Antenna: IPEX
Frequency: 5.8GHz 9 bands 72 channels, with Raceband
Size: 23*23mm(L*W),Hole:20*20mm
Weight: 2.2g
Package Includes:

1x HGLRC F4 AIO OSD BEC Flight Controller Board
1x HGLRC 28A Blheli_S 4 In 1 ESC
1x HGLRC XJB-TX20 Mini FPV Transmitter
1 x IPEX Dipole Antenna
1 x Standoff Kit
Warning: As with all video transmitters, do not power up the unit unless you have the antenna connected. Powering up a video transmitter with the no antenna will destroy the transmitter.

Note: Incorrect soldering techniques will damage this board and possibly void warranty. Please use the correct sized tip, temperature and technique. Temp controlled soldering irons (such as the TS100) are available for under $100 and will make soldering much easier.

$94.95
$94.95


In Stock: Totally in stock right now

HP-WR-002 Hyperion Universal Female Servo Lead 300mm


HP-WR-002 Hyperion Universal Female Servo Lead 300mm

$3.30
$3.30


In Stock: Totally in stock right now

HP-WR-005 Hyperion Servo Extension Lead 300mm


HP-WR-005 Hyperion Servo Extension Lead 300mm

$4.30
$4.30


In Stock: Totally in stock right now

HP-WR-006 Hyperion Servo Extension Lead 600mm


HP-WR-006 Hyperion Servo Extension Lead 600mm

$5.10
$5.10


In Stock: Totally in stock right now

HP-WR-007 Hyperion Servo Extension Lead 1000mm


HP-WR-007 Hyperion Servo Extension Lead 1000mm

$6.00
$6.00


In Stock: Totally in stock right now

HP-WR-009 Hyperion Light Servo Extension Lead 200mm


HP-WR-009 Hyperion Light Servo Extension Lead 200mm

$3.70
$3.70


In Stock: Totally in stock right now

HP-WR-010 Hyperion Light Servo Extension Lead 300mm


HP-WR-010 Hyperion Light Servo Extension Lead 300mm

$4.50
$4.50


In Stock: Totally in stock right now

HP-WR-011 Hyperion Light Servo Extension Lead 500mm


HP-WR-011 Hyperion Light Servo Extension Lead 500mm

$4.60
$4.60


In Stock: Totally in stock right now

HP-WR-014 Hyperion Light Y Lead Connector 180mm


HP-WR-014 Hyperion Light Y Lead Connector 180mm

$8.40
$8.40


In Stock: Totally in stock right now

HXT Micro T-Connector Style Plugs


HXT Micro T-Connector Style Plugs

Great for small applicaions like tiny helicopters and foam planes.

Includes: 1x pair of plugs.

$3.00
$3.00


In Stock: Sorry bro, Sold out

HYPERdrive clutch bearing set(2)


Note: Always inspect clutch bearings for damage after a crash. Bearings should always engage without backlash. To replace bearing you will need to use a 3mm SHCS to offset inside the coupler(there is a gap between the bearing and the bottom of the bearing bore). You can then use a spare shaft to press out the bearing. Note the bearing orientation when pressing it back in. If you do not have access to an arbor press, we recommend just purchasing a replacement coupler with bearing.

$15.00
$15.00


In Stock: Totally in stock right now

Hyperion 2x Gold 3.5mm Connector with insulators


HP-FG-CON35-2P
Hyperion 2x Gold 3.5mm Connector with insulators

�Ideal for Hyperion FG LiFE receiver packs

$4.80
$4.80


In Stock: Totally in stock right now

Hyperion Balance Board 2S-7S - TP/FP Style


Hyperion Balance Board for 7S chargers such as the Super Duo and EOS 0720i chargers. For use with 2S-7S batteries. Board only - for use with batteries such as Thunder Power, Flightpower, Outrage and other similar types.

$7.00
$7.00


In Stock: Totally in stock right now

Hyperion EOS Sentry Battery Checker V3


The Latest 2016 Model Hyperion Sentry 3 Battery Balancer, Checker, and Discharger

Product Description
The EOS Sentry3 is a quick, clever, and convenient device for analyzing your batteries. The Sentry3 shows at a glance the remaining capacity in your battery pack, cell balance, cell voltages and gap.Stand-alone Balance and Store Modes at industry-leading discharge performance.Sentry 3 provides the information and tools you need to maintain top performance and reliability from your batteries, and to avoid costly mistakes.

Features
2S ~ 8S Battery compatible with HvLi LiPo, Standard LiPo, LiFe. NiCd, and NiMh capable

EOS Sentry 3 displays the total battery pack voltage and a percentage bar graph for estimated remaining capacity

View screens for Minimum and Maximum cell voltages, and max cell Gap

Store Mode allows you to discharge your battery to 3.8V (Discharge rate is a powerful 150mah)
Balance Mode tunes your pack for performance automatically

5 ~ 25V auxiliary input voltage check port using JST 2-pin connectors on pack side
Large clear display and easy-to-use menu

Powered from the battery pack you connect for testing. No batteries needed for device.
Store Mode: Allows you to discharge your HvLi, LiPo, LiFe to 3.8V for storage. Discharge rate for Store mode is 150mah and will cutoff to 3.8V.

Balance Mode: Will automatically discharge the individual lithium-based cells such that they are closely balanced, if balance can be obtained while all cells remain at or above 3.8V.

This battery checker is compatible with JST-XH balance adapter when you use directly otherwise require each type of balance board adapter.

In order to use Sentry 3 with the legacy Hyperion G3 packs with Hyperion-style balance connector, connect the battery Sentry 3 via HP-EOSLBA-26CBL cable + HP-EOSLBA-26HP-B multi-adapter board or HP-EOSLBA-7UCBL cable + HP-EOSLBA-7U-B multi-adapter board.

These cable&adapter sets are included with Hyperion 6S and 7S chargers.Hyperion G3 packs produced after mid-2014 and all Hyperion G6 HvLi packs use XH balaance connectors and need no adapters to the Sentry 3.

NiMh can be checked between 5V~25V using JST connector

$35.00
$35.00


In Stock: Totally in stock right now

Hyperion G3 CX 11.1V 3S 120mAh 25C/45C Battery


* Weight: 16g
* Dimensions: 39 x 22 x 17 mm
* G3 Technology Lipo
* Capacity and Resistance Matched Cells
* 5C Speed Charging OK
* 4 x Longer Cycle Life

Hyperion Generation 3 Lithium Polymer Packs are proving truly revolutionary in both performance and value. Compared to an average of the batteries on market last year, they provide up to up to 4x more cycles under the same discharge conditions. And that makes them a bargain price-wise.

But they also deliver the highest voltage and flattest discharge curves under load that we have ever seen, which makes them the best performer you can buy. And tests have shown that at the 70%-discharged point in flight, they are delivering as much as 40% more power than previous generation LiPo.

The fact that they can be safely charged at up to 5C rates - for charge times as low as 10 to 12 minutes - is just icing on a very tasty cake.

The G3 packs depend on a new Hybrid RS construction technology, super-fine substrate materials, and a rigorous Quality Control and cell matching process, in order to guarantee you not only this superb performance, but also tightly balanced and long-lasting packs.

The G3 LiPo come in two series. "CX" 25C are appropriate for most models and deliver high capacity and power per gram at low cost. The "VX" 35C series is the one for applications that need the highest possible voltage maintained at high discharge rates; for example highly aerobatic 3D airplanes and helicopters, competition gliders, pylon racers, and some EDF jets.

Check'm out, you'll be glad you did.

*Note, picture is of the 2S Battery

$18.00
$18.00


In Stock: Totally in stock right now

Hyperion G3 CX 11.1V 3S 450mAh 25C/45C Battery


•Weight: 42g
•Dimensions: 58 x 32 x 17.5 mm
•G3 Technology Lipo
•Capacity and Resistance Matched Cells
•5C Speed Charging OK
•4 x Longer Cycle Life
Hyperion Generation 3 Lithium Polymer Packs are proving truly revolutionary in both performance and value. Compared to an average of the batteries on market last year, they provide up to up to 4x more cycles under the same discharge conditions. And that makes them a bargain price-wise.

But they also deliver the highest voltage and flattest discharge curves under load that we have ever seen, which makes them the best performer you can buy. And tests have shown that at the 70%-discharged point in flight, they are delivering as much as 40% more power than previous generation LiPo.

The fact that they can be safely charged at up to 5C rates - for charge times as low as 10 to 12 minutes - is just icing on a very tasty cake.

The G3 packs depend on a new Hybrid RS construction technology, super-fine substrate materials, and a rigorous Quality Control and cell matching process, in order to guarantee you not only this superb performance, but also tightly balanced and long-lasting packs.

The G3 LiPo come in two series. "CX" 25C are appropriate for most models and deliver high capacity and power per gram at low cost. The "VX" 35C series is the one for applications that need the highest possible voltage maintained at high discharge rates; for example highly aerobatic 3D airplanes and helicopters, competition gliders, pylon racers, and some EDF jets.

Check'm out, you'll be glad you did.

$21.50
$21.50


In Stock: Totally in stock right now