Product Search

Tinys LEDS - RaceLiteWire Mini LEDs (2-Pack) - Red


This is a 2 pack of RaceLiteWires
These are integrated Racewire and Racelites.
These can be installed in any direction.
There are pads to Allow you to wire up additional Racelites to the bottom of your Arms. Use the pads labeled "1,2,3" and wire them to the same pads on the second Racelite. You must insulate the bottom of the boards.

Specifications:

Dimensions:8 x 25 mm
Voltage: 3-6s
Contents: 2x RaceLiteWire

Check out how to use them HERE

View a video of the product in action.

$6.60
$6.60


In Stock: Totally in stock right now

Tinys LEDS - RaceLiteWire Mini LEDs (2-Pack) - White


This is a 2 pack of RaceLiteWires
These are integrated Racewire and Racelites.
These can be installed in any direction.
There are pads to Allow you to wire up additional Racelites to the bottom of your Arms. Use the pads labeled "1,2,3" and wire them to the same pads on the second Racelite. You must insulate the bottom of the boards.

Specifications:

Dimensions:8 x 25 mm
Voltage: 3-6s
Contents: 2x RaceLiteWire

Check out how to use them HERE

View a video of the product in action.

$6.60
$6.60


In Stock: Totally in stock right now

Tinys LEDS - RealPit VTX Power Switch


Features / Uses:

Plug in your VTx at any time with 0 power start-up
FlightOne may have a split-second power up on boot up. Some VTXs may transmit during that time.
Turn off your VTx on the line to avoid heat buildup
Fast Team Race Pit stops (Sub second transitions possible)
Compatible with all major VTxs
Turn off VTx during races to test hover builds without interfering with other pilots in the air.
Turn off VTx after Crash for clean video for other racers.
Solo Endurance Races, 3 quads ready on the line. Practice for more than 1 pack without taking off goggles. (Instructions on how to setup on OpenTX / Spektrum Coming soon)
LED Indicator light on board. (Light On \ Power On)
Can be used on any pad on Flight Controller.
Does not need a full UART.
I.E.: SmartAudio/Tramp on TX and RX for RealPit PinIO
Up to 4 RealPits per quad. This opens the possibility for LEDs, and VTX, and any other device you can imagine.
Toggle LED Power or any other devices under 1 amp draw.

Currently Supported Software:

Betaflight (PinIO 3.3.x or Greater)
Butterflight (PinIO)
FlightOne 1.2.4 + (PINTOGGLE)

Operating Voltage: 5V - 28V (HV-6s) 1Amp Switch

Dimensions: 10 x 12.5 x 2.5 mm

Weight: 0.5 Grams w/ Heatshrink

Demo Video:

Contents:

1x Realpit
1x 1/2" Heat shrink piece

Betaflight Settings:

In CLI:

Type RESOURCE

Locate UART TX/RX pad resource ID you are using. We wired to RX4 in this demo. RX4 is A01 Note the name of resource and ID.

Next we will clear that pad from its assigned resource.
Type
RESOURCE SERIAL_RX 4 NONE

Next we will set the Custom Mode Switches. We will set up 1 switch Copy and past these Commands into CLI:

set pinio_box = 40,41,42,43
aux 2 40 2 1600 2100 0

Next we need to assign the Resource ID to the Custom Mode switch. Using the Resource ID from above. "A01"
resource PINIO 1 A01

If you wish to set up more pads for additional RealPits. replace the area in brackets with your resource IDs: Copy these extra lines to add more modes as well.:

set pinio_box = 40,41,42,43
aux 3 41 3 1600 2100 0
aux 4 42 4 1600 2100 0
aux 5 43 5 1600 2100 0

resource PINIO 2 [resource=I.E=A04]
resource PINIO 3 [resource=I.E=A05]
resource PINIO 4 [resource=I.E=A06]

Type SAVE in CLI and then press enter. Your FC will reboot after applying changes.

Now go to Modes and Assign an AUX channel to the USER1 mode. Just like an arm or turtle mode switch. Click SAVE

Now flip the switch and test. A RED LED will be lit on RealPit if your are providing power.

$7.40
$7.40


In Stock: Totally in stock right now

Tinys LEDS - RGB RaceLiteWire LEDs (2-Pack)


RGB RaceLiteWire LEDs (2-Pack)

4x 5050 RGB LEDs integrated into Racewire.
This is a 2 pack of RGB RaceLiteWires Full Size
These are integrated Racewire and Racelites.
These can be installed in any direction.
There are pads to Allow you to wire up additional Racelites to the bottom of your Arms. Use the pads labeled "1,2,3" and wire them to the same pads on the second Racelite. You must insulate the bottom of the boards.

Specifications:

Dimensions:8 x 40 mm
Voltage: 3-6s
Contents: 2x RaceLiteWire

Check out how to use them HERE

View a video of the product in action.

$8.50
$8.50


In Stock: Totally in stock right now

Tinys LEDS - RGB RaceLiteWire Mini LEDs (2-Pack)


This is a 2 pack of RGB RaceLiteWires Minis
These are integrated Racewire and Racelites.
These can be installed in any direction.
There are pads to Allow you to wire up additional Racelites to the bottom of your Arms. Use the pads labeled "1,2,3" and wire them to the same pads on the second racelite. You must insulate the bottom of the boards.

Specifications:

Dimensions: 8 x 25 mm
Voltage: 3-6s
Contents: 2x RaceLiteWire

Check out how to use them HERE

View a video of the product in action.

$7.50
$7.50


In Stock: Totally in stock right now

Tinys LEDS - Tiny LED Blue


Have you been searching for a way to take your quad to the next level? Looking to add some flare to your flying? Add a few of these Tiny's Leds to your quads and your friends will enjoy watching you at races, or even just flippy floppying around the park.
Leds make everything better and Tiny’s Leds have created the best solution for our needs. These 3-6s direct voltage led chips bring to the table a tiny form factor of a mere 8x18mm and can be fit onto most arms!
Specification

Voltage: 3-6s / 12-26 Volt.
Size: 8 x 18 x 1.8 mm
Weight: 0.4 Grams
Power: 3x 0.5 watt LED Chips

$14.90
$14.90


In Stock: Totally in stock right now

Tinys LEDS - Tiny LED Green


Have you been searching for a way to take your quad to the next level? Looking to add some flare to your flying? Add a few of these Tiny's Leds to your quads and your friends will enjoy watching you at races, or even just flippy floppying around the park.
Leds make everything better and Tiny’s Leds have created the best solution for our needs. These 3-6s direct voltage led chips bring to the table a tiny form factor of a mere 8x18mm and can be fit onto most arms!
Specification

Voltage: 3-6s / 12-26 Volt.
Size: 8 x 18 x 1.8 mm
Weight: 0.4 Grams
Power: 3x 0.5 watt LED Chips

$14.90
$14.90


In Stock: Totally in stock right now

Tinys LEDS - Tiny LED Red


Have you been searching for a way to take your quad to the next level? Looking to add some flare to your flying? Add a few of these Tiny's Leds to your quads and your friends will enjoy watching you at races, or even just flippy floppying around the park.

Leds make everything better and Tiny’s Leds have created the best solution for our needs. These 3-6s direct voltage led chips bring to the table a tiny form factor of a mere 8x18mm and can be fit onto most arms!
Specification

Voltage: 3-6s / 12-26 Volt.
Size: 8 x 18 x 1.8 mm
Weight: 0.4 Grams
Power: 3x 0.5 watt LED Chips

$14.90
$14.90


In Stock: Totally in stock right now

Tinys LEDS - Tiny LED White


Have you been searching for a way to take your quad to the next level? Looking to add some flare to your flying? Add a few of these Tiny's Leds to your quads and your friends will enjoy watching you at races, or even just flippy floppying around the park.
Leds make everything better and Tiny’s Leds have created the best solution for our needs. These 3-6s direct voltage led chips bring to the table a tiny form factor of a mere 8x18mm and can be fit onto most arms!
Specification

Voltage: 3-6s / 12-26 Volt.
Size: 8 x 18 x 1.8 mm
Weight: 0.4 Grams
Power: 3x 0.5 watt LED Chips

$14.90
$14.90


In Stock: Totally in stock right now

Tinys LEDS - Tiny Rainbow RGB LEDs


THESE ARE 5 Volt ONLY

Please do not power these from anything high than 5 volts. You will fry them.

4 LED 5050 Addressable RGB Rigid Boards
Size: 8 x 29 x 2.25mm
Current Draw: 240mA on Full White, Less with other colors.
Fully addressable via flight controller.
Data in and out on each side for easy wiring and daisy chaining.
These will fit on a WhitenoiseFPV's Racewire boards. You must use some isolation between boards to prevent short circuits.
These LEDs do not have the small capacitor like other boards. This is to provide more clean power to the LEDs. I have been running them without for a while and no issues. They were removed to make smaller boards. This will be great for 2"-7"!

$4.40
$4.40


In Stock: Totally in stock right now

Tinys LEDS - WhitenoiseFPV TBS Unify Mounting Board w/ RealPit


WhitenoiseFPV TBS Unify Mounting Board w/ RealPit

Features / Uses:

Plug in your VTx at any time with 0 power start-up
FlightOne may have a split-second power up on boot up. Some VTXs may transmit during that time.
Turn off your VTx on the line to avoid heat buildup
Fast Team Race Pit stops (Sub second transitions possible)
Compatible with TBS Unify Nano, 5v Pro, HV v3
Mounting for Receiver on bottom of board. XM+ or XF easy mount
Turn off VTx during races to test hover builds without interfering with other pilots in the air.
Turn off VTx after Crash for clean video for other racers.
Solo Endurance Races, 3 quads ready on the line. Practice for more than 1 pack without taking off goggles. (Instructions on how to setup on OpenTX / Spektrum Coming soon)
LED Indicator light on board. (Light On \ Power On)
Can be used on any pad on Betaflight Flight Controller.
BUILT-IN capacitors for 5v camera/vtx power and Lipo battery voltage. (Clean up video lines)
Please see Image for Pin-Out Diagram

Currently Supported Software:

Betaflight (PinIO)
Butterflight (PinIO)
FlightOne 1.2.4+ (PINTOGGLE)

Operating Voltage: 5V - 28V (HV-6s) 1Amp Switch

Dimensions: 36 x 36 x 2.5 mm

Weight: 2.5 Grams w/ Heatshrink

Contents:

1x Realpit
1x 1/2" Heat shrink piece

Betaflight Settings:

In CLI:

Type RESOURCE

Locate UART TX/RX pad resource ID you are using. We wired to RX4 in this demo. RX4 is A01 Note the name of resource and ID.

Next we will clear that pad from its assigned resource.
Type
RESOURCE SERIAL_RX 4 NONE

Next we will set the Custom Mode Switches. We will set up 4 switches for up to 4 Realpits. Copy and past these Commands into CLI:

set pinio_box = 40,41,42,43
aux 2 40 2 1600 2100 0
aux 3 41 3 1600 2100 0
aux 4 42 4 1600 2100 0
aux 5 43 5 1600 2100 0

Next we need to assign the Resource ID to the Custom Mode switch. Using the Resource ID from above. "A01"
resource PINIO 1 A01

If you wish to set up more pads for additional RealPits. replace the area in brackets with your resource IDs:

resource PINIO 2 [resource=I.E=A04]
resource PINIO 3 [resource=I.E=A05]
resource PINIO 4 [resource=I.E=A06]

Type SAVE in CLI and then press enter. Your FC will reboot after applying changes.

Now go to Modes and Assign an AUX channel to the USER1 mode. Just like an arm or turtle mode switch. Click SAVE.

Now flip the switch and test. A RED LED will be lit on RealPit if your are providing power.

$11.70
$11.70


In Stock: Totally in stock right now

TinySnapper (Canon)


The TinySnapper offers a very simple way of controlling your digital camera from your RC system and it’s really affordable.

Just plug in the TinySnapper where you normally plug in a servo motor – when you flip the switch on your remote, the TinySnapper will trigger your camera via an infrared transmitter.

I doesn’t get any simpler! The TinySnapper is preprogrammed to work with a specific brand, and triggers the shutter when the servo signal is a bit above neutral.

Please remember that most cameras need to be setup to accept IR remote and you need to disable auto power-off.

Mounting is easy. The TinySnapper has a flexible neck which allows you to point the transmitter in the direction of the IR receiver on your camera. It also comes with some Dual Lock re-closeable fasteners for mounting.

The TinySnapper comes in many flavors! Currently all mayor camera brand are supported, but be sure to pick the type that suits you camera when ordering. The TinySnapper currently supports triggering of more than 100 camera types. Check out the supported cameras page.

Specifications:

Takes a standard servo input and converts it into an infrared remote camera trigger signal.
Accepts standard 5V servo power. (don’t push it beyond 6.5V).
Very low weight and form factor.
Flexible neck for precise positioning.
Dual Lock re-closeable fasteners included for easy mounting.
35 cm servo cable.
Ultra bright IR transmitter for reliable communication.
Lead free. RoHS compliant.
If you are looking for a more customizable solution check out the StratoSnapper

$21.00
$21.00


In Stock: Totally in stock right now

TinySnapper (Nikon)


The TinySnapper offers a very simple way of controlling your digital camera from your RC system and it’s really affordable.

Just plug in the TinySnapper where you normally plug in a servo motor – when you flip the switch on your remote, the TinySnapper will trigger your camera via an infrared transmitter.

I doesn’t get any simpler! The TinySnapper is preprogrammed to work with a specific brand, and triggers the shutter when the servo signal is a bit above neutral.

Please remember that most cameras need to be setup to accept IR remote and you need to disable auto power-off.

Mounting is easy. The TinySnapper has a flexible neck which allows you to point the transmitter in the direction of the IR receiver on your camera. It also comes with some Dual Lock re-closeable fasteners for mounting.

The TinySnapper comes in many flavors! Currently all mayor camera brand are supported, but be sure to pick the type that suits you camera when ordering. The TinySnapper currently supports triggering of more than 100 camera types. Check out the supported cameras page.

Specifications:

Takes a standard servo input and converts it into an infrared remote camera trigger signal.
Accepts standard 5V servo power. (don’t push it beyond 6.5V).
Very low weight and form factor.
Flexible neck for precise positioning.
Dual Lock re-closeable fasteners included for easy mounting.
35 cm servo cable.
Ultra bright IR transmitter for reliable communication.
Lead free. RoHS compliant.
If you are looking for a more customizable solution check out the StratoSnapper

$21.00
$21.00


In Stock: Totally in stock right now

Trueblood TREX 250 Swashplate Leveler


T-Rex 250 Swash Plate Leveler
This is the original Trueblood Swashplate Leveler by Trueblood Engineering. Proudly Made in the USA.

Bench User Guide

Compatible Helicopters

Click here for more information

$19.50
$19.50


In Stock: Totally in stock right now

Trueblood Vibe 50 Swashplate Leveler


Vibe 50 Swash Plate Leveler
This is the original Trueblood Swashplate Leveler by Trueblood Engineering. Proudly Made in the USA.

Bench User Guide

Compatible Helicopters

Click here for more information

$39.00
$39.00


In Stock: Totally in stock right now

TS100 Digital OLED Programmable Soldering Iron


The TS100 Digital OLED Programmable Soldering Iron is an internal heating intelligent CNC soldering iron. It is easy to assemble and disassemble for storage and portability. It has a comfortable handle and the highly effective heating function makes it an indispensable tools for any hobbyist. It is made from high quality metal & plastic materials and assembled with great workmanship, for high durability and reliability.

Our favourite feature of the TS100 is it's ability to be so mobile. It can easily be powered by a 4s lipo battery while on the go, no A/C outlet required. This means you can make quick fixes while out at the field. The iron heats up to operating temperature in under 15 seconds! This is a must have for any RC enthusiast.

Features

Built-in acceleration sensors with STM32 chip can intelligently record your usage habits
Bright OLED screen is clear easy for you to read information
Digital temperature readout
Temperature control button is set on the handle allowing for easy temperature adjustments
Anti-static structure with ground wire ensures your safety during use
Supports custom programmable development (Micro USB Connection)
Multiple soldering head types are available (Up to 7)
Can be powered via a 3-4s LiPo battery for mobile use

Specifications

Model TS100
Material Metal & Plastic
Power 65W
Special Function Programmable, Temperature Adjustment
Voltage(V) 12-24V
Temperature Control Support Yes
Adjustable Temperature Range 100 Centigrade - 400 Centigrade
Heating Type Internal Heating
Working Temperature 300 Centigrade
Color Black
Dimensions (6.61 x 0.67 x 0.51)" / (16.8 x 1.7 x 1.3)cm (L x W x H)
Weight 0.74oz / 21g

Package Includes

1 x TS100 Digital LCD Soldering Iron
1 x TS-I Solder Tip (please note not all product pictures depict this - please see chart)
1 x Allen Wrench
2x Extra Locking Screws
1 x Bilingual Manual in English and Chinese

$84.95
$84.95


In Stock: Sorry bro, Sold out

TS100 Soldering Iron XT60-DC Cable


Power your TS-100 soldering iron easily from an XT60 battery using this handy XT-60 to 2.5mm DC jack cable - designed specifically for the TS-100.

Please Note: Actual product may differ slightly from product picture.

$6.95
$6.95


In Stock: Totally in stock right now

Turnigy Hex Socket Driver Set - 4pc


High strength and light weight.

The 4pc TURNIGY hex socket driver set includes sizes 4.0B, 4.5B, 5.5B and 7.0B.

Made from high strength tool steel, these tools reduce rounding and ensure a secure screw fit each time.

$15.00
$15.00


In Stock: Sorry bro, Sold out

Turnigy High Density R/C LED Flexible Strip-Blue (1mtr)


Turnigy High Density light strips come with 60 LEDs per meter!!
LEDs are arranged in sets of 3, you can cut the strip and make new strips or extend strips to make any combination of 3 lights!

Features:
Comes with adhesive tape backing for easy mounting
Flexible enough to be bent at any angle
Easy to use. Just peel and stick!
Large voltage input range up to 12V DC! (Great for 2-3S Lipoly)

Specifications:
Standard length: 1 meter
Strip width: 8mm
LED quantity per strip(1 mtr): 60 LEDs
Working voltage: DC12V
Working current(1mtr): 400mA
Wire length(1mtr): 10cm
Weight including wire(1mtr): 11g

$22.00
$22.00


In Stock: Totally in stock right now

Turnigy High Density R/C LED Flexible Strip-Green (1mtr)


Turnigy High Density light strips come with 60 LEDs per meter!!
LEDs are arranged in sets of 3, you can cut the strip and make new strips or extend strips to make any combination of 3 lights!

Features:
Comes with adhesive tape backing for easy mounting
Flexible enough to be bent at any angle
Easy to use. Just peel and stick!
Large voltage input range up to 12V DC! (Great for 2-3S Lipoly)

Specifications:
Standard length: 1 meter
Strip width: 8mm
LED quantity per strip(1 mtr): 60 LEDs
Working voltage: DC12V
Working current(1mtr): 400mA
Wire length(1mtr): 10cm
Weight including wire(1mtr): 11g

$22.00
$22.00


In Stock: Totally in stock right now

Turnigy High Density R/C LED Flexible Strip-Red (1mtr)


Turnigy High Density light strips come with 60 LEDs per meter!!
LEDs are arranged in sets of 3, you can cut the strip and make new strips or extend strips to make any combination of 3 lights!

Features:
Comes with adhesive tape backing for easy mounting
Flexible enough to be bent at any angle
Easy to use. Just peel and stick!
Large voltage input range up to 12V DC! (Great for 2-3S Lipoly)

Specifications:
Standard length: 1 meter
Strip width: 8mm
LED quantity per strip(1 mtr): 60 LEDs
Working voltage: DC12V
Working current(1mtr): 400mA
Wire length(1mtr): 10cm
Weight including wire(1mtr): 11g

$22.00
$22.00


In Stock: Totally in stock right now

Turnigy High Density R/C LED Flexible Strip-White (1mtr)


Turnigy High Density light strips come with 60 LEDs per meter!!
LEDs are arranged in sets of 3, you can cut the strip and make new strips or extend strips to make any combination of 3 lights!

Features:
Comes with adhesive tape backing for easy mounting
Flexible enough to be bent at any angle
Easy to use. Just peel and stick!
Large voltage input range up to 12V DC! (Great for 2-3S Lipoly)

Specifications:
Standard length: 1 meter
Strip width: 8mm
LED quantity per strip(1 mtr): 60 LEDs
Working voltage: DC12V
Working current(1mtr): 400mA
Wire length(1mtr): 10cm
Weight including wire(1mtr): 11g

$22.00
$22.00


In Stock: Totally in stock right now

Turnigy XT60 Plug (Pair)


Made from high-temp Nylon and gold plated spring connectors, both included in the injection mould at the time when forming the connector. The XT60 ensures a solid high-amp connection, perfect for applications up to and beyond 65A constant.

$1.60
$1.60


In Stock: Totally in stock right now

VT-A-1111 - Voltz 11 to 11 Pin Balancing Cable


$4.00
$4.00


In Stock: Totally in stock right now

VT-A-TMP - Voltz Temperature Sensor with Magnet


Temperature sensor plugs into your Voltz charger and is intended to monitor your batteries while charging.

$13.00
$13.00


In Stock: Totally in stock right now

WhitenoiseFPV Nano-Nano TBS Unify / Crossfire Nano Mounting Board


The Nano-Nano board was designed to allow you to mount your Team BlackSheep Unify Pro Nano VTX in your stack for cleaner builds. This board includes holes that are compatible with (but not limited to) most receivers such as the FrSky XM+ and Team BlackSheep Crossfire Nano. Once the VTX is soldered into the cutout on the board, the breakout pads on the side allow for full access to your VTX.

If your camera uses 5V for power, you can solder your pigtail to the camera pads and allow the board to act as a pass through. After your VTX, camera, and receiver is installed, the 5V pad on the board will power all your components.

There are also two pads located on the side of the board to solder the button that's included with your Unify Nano. The button can be soldered top facing, side facing, or with wires to allow for access to the VTX from anywhere.

Note: If your receiver requires 3V, you will need to pull power from somewhere else. Do not solder in the 5V header if your receiver is not compatible. You can use the other plated through holes (1, 2, and ground) for your receiver still.

FEATURES
TBS Unify Pro Nano Video Transmitter support
4 plated through holes for mounting receivers
Pads for camera pigtail
Top or side pads for VTX button
20mm x 20mm hole pattern
27mm x 26mm dimensions

$8.95
$8.95


In Stock: Totally in stock right now

Wire Mesh Guard Black 10mm (1M)

Wire Mesh Guard is an excellent way to protect servo leads or battery wires.

$2.50
$2.50


In Stock: Totally in stock right now

Xnova 2204 Replacement Bearing Set


1 x High quality replacement bearing set

(4 bearings)

Suits Xnova 2204 series motors

$33.90
$33.90


In Stock: Totally in stock right now

Xnova 2204 Replacement Shaft Set


Replacement shaft for Xnova 2204 size motors

Package contains: 4 x 2204 Replacement Shafts

$8.90
$8.90


In Stock: Totally in stock right now

Xnova 2206 Replacement Bearing Set


1 x High quality replacement bearing set

(4 bearings)

Suits Xnova 2206 series motors

$33.90
$33.90


In Stock: Totally in stock right now

Xnova 2206 Replacement Shaft Set


Replacement shaft for all Xnova 2206 size motors

Package contains: 4 x 2206 Replacement Shafts

$8.90
$8.90


In Stock: Totally in stock right now

Xnova 2206-2300kv Supersonic Brushless Motor (Single)


Xnova motors are made from the finest components available today and guaranteed for the highest levels of performance and efficiency. Each Xnova motor is 100% hand wound and guaranteed to perform. Be convinced by the results, not just datasheets.

High performance
Finest CNC quality
Ultimate efficiency
Low cogging torque
Smooth running
Precise balancing
Fully tested
100% hand wound
5″ to 6″ Prop Size

$15.00
$15.00


In Stock: Totally in stock right now

XT60 SmokeStopper Tool


XT60 SmokeStopper - Termed the SmokeStopper by RCgroups member mnemennth, this handy device could save you from damaging expensive electronic components

We've all been there... Working all day on a new build, you finally finish, you give your new beast one final look-over and don't see anything wrong. So you plug it in and TZZZT! SNAPP! POP! and instantly, your plans for new-found aerial bliss disappear literally in a puff of smoke.

You tear it down and find a blown ESC caused by a motor with a too-long screw into a winding or a little blob of solder that you SHOULD have caught before you put the new shrink-wrap on, but DIDN'T.

Now you have to tear it apart and replace the toasted ESC before you can even see if the motor is salvageable. You already know you're going to be ordering a new one shortly; the only difference is whether you're going have to wait for it to come in the post or if you ordered enough to have a spare and will need to replace it.

$14.95
$14.95


In Stock: Totally in stock right now